|
Technical & Industrial Division - Collision
Technology Center, Rm. 108
|
First year tool list
Second year tool list |
|
Tool
box (Top or bottom box) - both years
| Screw
drivers |
Hex key wrench set (Allen) |
|
Slotted set |
Standard set |
| Philips, #1 #2 #3 #4 |
Metric set |
|
Torx, T-10, T-15, T20, T-25, T-27, T-30 |
|
|
¼ inch drive socket set |
3/8 inch drive socket set |
|
Ratchet |
Ratchet |
|
3 inch extension & 6 inch extension |
3 inch extension & 6 inch extension |
|
Driver handle |
S.A.E. six point deep sockets, 3/8, 7/16,
1/2, 9/16, 5/8,11/16, 3/4 |
|
S.A.E. six point deep sockets, 1/4, 5/16,
11/32, 3/8 7/16, 1/2 |
S.A.E. six point shallow sockets, 3/8, 7/16,
1/2, 9/16, 5/8, 11/16, 3/4 |
|
S.A.E. six point shallow sockets, 1/4, 5/16,
11/32, 3/8, 7/16, 1/2 |
Metric six point deep sockets, 10mm, 11mm,
12mm, 13mm, 14mm, 15mm, 17mm, 18mm, 19mm |
|
Metric six point deep sockets, 4mm, 5mm, 6mm,
7mm, 8mm, 9mm, 10mm, 11mm, 12mm, 13mm. |
Metric six point shallow sockets, 10mm, 11mm,
12mm, 13mm, 14mm, 15mm, 17mm, 18mm, 19mm |
|
Metric six point shallow sockets, 4mm, 5mm,
6mm, 7mm, 8mm, 9mm, 10mm, 11mm, 12mm, 13mm |
|
| Pliers |
Hammers |
|
6-inch side cutting |
3lb. Blacksmith hammer. (Cross peen) |
|
6-inch needle nose |
Cross-peen hammer |
|
6-inch channel locks |
Pick hammer |
|
10-inch channel locks |
Finishing hammer |
| General purpose hand
dolly |
Light dinging spoon |
|
Clamps |
Measuring tools |
|
Two 9R Vise-grip |
12 foot measure tape with metric scale |
|
Two 11R Vise-grip |
36 inch metal straight edge |
| Combination wrench
sets |
Sanding tools |
|
S.A.E. 1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8,
11/16, 3/4, 13/16, 7/8, 15/16 |
17 inch sanding board. (adhesive type) |
|
Metric, 7mm, 8mm, 9mm, 10mm, 11mm, 12mm,
13mm, 14mm, 15mm, 17mm, 18mm, 19mm |
Sanding block (adhesive type) |
|
Miscellaneous body tools |
Clip tools |
|
6-10 inch ice pick. (Awl) |
Windshield molding release tool |
|
Blow gun. (Rubber tipped) |
Windshield wiper remover |
|
1-inch stiff putty knife |
Door handle clip remover |
|
3-inch flexible putty knife |
Trim panel tool. (V-notch) |
|
12 volt circuit tester |
Digital Multimeter |
|
Body file and holder |
|
|
Safety equipment |
|
Face shield |
|
Safety glasses |
|
Safety goggles |
|
Hearing protectors. (Ear muff type) |
END First year
- back to top
|
|
|
|
|
Air ratchets |
Sanders/grinders |
| ¼ in. drive air ratchet |
6 in. air, Dual Action
sander |
| 3/8 in. drive air ratchet |
5 in. air grinder |
| ½ in. drive impact |
¼ in. air cut-off die
grinder |
|
Spray guns |
Impact sockets |
|
Primer gun |
½ in. drive SAE deep |
|
Color/Clear gun |
½ in. drive
metric deep |
END Second year
- back to top |
|
Entry level tool sets may or may not be as complete as
those listed on the complete tool list. You must have some of the
set and complete the set as you progress in the courses. Consult with
your advisor before purchasing tools if possible. In addition to the
ELT tools is the list of tools required for the duration of the program.
Sets that are listed, is an economical way to purchase tools.
Fall tool fair will give the students
opportunities to purchase tools from a variety of vendors at a discounted
rate. The tool fair is held the first Friday of the fall semester. |
