Technical & Industrial Division

Tool List Diesel Technology

Roll cabinet toolbox

Cape 1/4" or 1/16" Chisel

Diamond Point 7/32" or 1/8" Chisel

Flat 1/2" Chisel

Flat 3/4" Chisel

Circuit tester or test light (12 and 24 volt capability preferred, 12 volt will suffice)

10" round, tapered file

12" flat mill, bastard, single cut file

12" three square, bastard, single cut file

Two or three cell MagLight or similar style

Feeler - 45 degree angle, .006" through .35" gauge

Feeler - .0015" through .34", go-no-go style gauge

Thread pitch, metric gauge

Thread pitch, standard SAE

Digital caliper, metal 0-6"

Hacksaw: Frame and blades - (24 and 32 teeth per inch)

Ball peen 8 oz. hammer

Ball peen 16 oz. hammer

Ball peen 40 oz. or 4 lbs. soft face drilling hammer

3 to 5 lbs.. Dead blow with soft face hammer

Jumper Wires: Two each, 2 to 3 feet long with alligator clips, 12 gauge

Magnet: Mechanics style with handle about 12" long

Pocket Rule: 6" standard and metric with pocket clip

Outside 0" to 1" capability, SAE micrometer

Meter:Volt, Ohm, Amps with digital readout and high impedance (Fluke mfr. Brand, model 115)

Tri-Square: Steel combo 12"

Combination slip joint style 6" pliers

Diagonal cutting 7 1/4" pliers

Interlocking/adjustable joint 12" pliers

Locking type, standard 8" pliers

Needle nose 7 1/4" pliers

Long tip, 3/8", length 15" punch

Brass drift, 1/2" diameter 10 to 12" in length punch

Brass drift, tapered 10 to 12" in length punch

Center punch, 3/8"

Pin, set of 6 (3/32", 1/8", 5/32", 3/16", 1/4" 5/16") punch

Starter, set of 5 (1/8", 5/32", 3/16", 1/4", 5/16") punch

Phillips, #1-3"

Phillips, #2 - 1 1/2"

Phillips, #2 - 4"

Phillips, #2 - 8"

Phillips, #3 - 6"

Torx Set #T10 thru #T30

Standard, 3/16" x 3"

Standard, 1/4" x 4"

Standard, 1/4" x 1 1/2"

Standard, 5/16" x 8"

Standard, 3/8" x 12"

3/8" Drive Ratchet

3/8" Driver 3, 6, 12" extensions

3/8" Drive Standard (SAE) 10 pc socket set, 1/4" thru 3/4" (12 point)

3/8" Driver Metric 13pc socket set, 6mm thru 19mm (12 point)

3/8" Driver Universal swivel socket

1/2" Drive Ratchet

1/2" Drive Standard (SAE) 15pc socket set 3/8" thru 1 1/4" (12 point)

1/2" Drive Metric 18pc socket set 10mm thru 27mm (12 point)

1/2" Drive 3, 5, 10" Extensions

1/2" Drive Breaker bar 18" to 24" long

Combination, 5/16" thru 1 1/4" (12 point) wrench

Combination, 6mm thru 22mm (12 point) wrench

Tubing wrenches, 1/4" thru 7/8" (6 point)

Adjustable wrench 10"

Adjustable wrench 12"

Allen (hex) wrenches, 5/64" thru 3/8"

Allen (hex) wrenches, 2mm thru 12mm

12ft standard and metric scale or something similar tape measure

Tubing Cutter

Scissors

Pocket Scribe

Scientific Calculator

Set of 4 O-Ring Picks

Torque wrench: 3/8" Drive 15 to 100lbs. FT

Scraper

Torque wrench: 1/2" Drive 30 to 250 ft lbs.

Remote Starter Switch: Heavy duty style, 12 gauge wire

Torque wrench: dial ¼” Drive inch pound

12 SNP RNG plier set Snap ring pliers flat tip

Safety Glasses: Z-87 with side shields
 

Pry bar set -3 sizes

15" with 13/16" edge pinch bar

Rubber tipped and OSHA approved Air Blow Gun

Tubing metric, 8mm thru 17mm wrench

Thread file set (metric and standard)

Double flaring kit

File set w/red vinyl

6 pc vise set

Optional Tool List (Will be needed when entering into the workforce):

5pc Battery service kit

20" straight edge

Mechanical fingers pick-up tool

Mechanics mirror

3/8" Drive Flex socket et, 3/8" thru 3/4"

0-1” Dial Indicator with a Conforming adjustable magnetic base

3/8" Drive Socket set standard (SAE) and metric deep (6 point)

1/2" Drive 600 ft. lbs. air impact wrench

1/4" Drive Ratchet

3/8" Drive 150 ft. lbs. air impact wrench

1/4" Drive Metric socket set, 6mm thru 15mm (6 or 12 point)

1/4" Drive 2”, 4”, 6" Extensions