Technical & Industrial Division

Tool Kit Diesel Technology

MISC. TOOLS PUNCHES
0-1" Dial indicator with a conforming adjustable magnetic base Punch, Brass drift, tapered 10 to 12" in length 
1/4" Die grinder with attachments Punch, Center punch, 3/8"
12ft standard and metric scale or something similar tape measure Punch, Long tip, 3/8", length 15" 
5 pc battery service kit Punch, Pin, set of 6 (3/32", 1/8", 5/32", 3/16", 1/4" 5/16") 
Digital caliper, metal 0-6" Punch, Starter set of 5 (1/8", 5/32", 3/16", 1/4", 5/16") 
Flashlight RATCHETS AND SOCKETS
Mechanical fingers pick-up tool 1/2" Drive 3, 5, 10" Extensions
Mechanic's mirror 1/2" Drive 600 ft lbs. air impact wrench
Mechanic's style magnet with handle about 12" long 1/2" Drive Breaker bar 18" to 24" long
Outside 0" to 1" capability, SAE micrometer 1/2" Drive Metric 18pc socket set 10mm thru 27mm (12 point)
Roll cabinet toolbox 1/2" Drive Ratchet
Rubber tipped and OSHA approved Air Blow Gun 1/2" Drive Standard (SAE) 15pc socket set 3/8" thru 1 1/4" (12 point)
Safety Glasses: Z-87 with side shields 1/4" drive 2", 4", 6" extensions
Scraper 1/4" Drive ratchet
Set of 4 O-ring picks 1/4" drive socket set, metric and standard
Soldering tool, electric or butane 3/8" Drive 150 ft lbs. air impact wrench
BARS 3/8" Drive flex socket et, 3/8" thru 3/4"
Heel bar set - 3 sizes 3/8" Drive Ratchet
Pry bar set -3 sizes 3/8" Drive socket set standard (SAE) and metric deep (6 point)
CHISELS 3/8" Drive Standard (SAE) 10 pc socket set, 1/4" thru 3/4" (12 point)
Chisel, Cape 1/4" or 1/16"  3/8" Driver 3, 6, 12" extensions
Chisel, Diamond Point 7/32" or 1/8"  3/8" Driver Metric 13pc socket set, 6mm thru 19mm (12 point)
Chisel, Flat 1/2"  3/8" Driver Universal swivel socket
Chisel, Flat 3/4"  Torx Set #T10 thru #T45
FEELERS TESTING TOOLS
Feeler - .0015" through .34", go-no-go style gauge Circuit tester or test light (12 and 24 volt capability preferred, 12 volt will suffice)- LED and incandescent
Feeler - 45 degree angle, .006" through .35" gauge
FILES Fluke TLK 289 test lead set
10" round, tapered file Meter: Volt, Ohm, Amps with digital readout and high impedance (Fluke mfr. Brand, model 87V)
12" flat mill, single cut file
12" three square single cut file SCREWDRIVERS
HAMMERS Screwdrivers, Phillips, 5 pc set
Hammer, 3 to 5 lbs. Dead blow with soft face  Screwdrivers, Standard, 5 pc set
Hammer, Ball peen 16 oz.  THREAD PITCH GAUGE
Hammer, Ball peen 40 oz. or 4 lbs. soft face drilling  Thread pitch, metric gauge Thexton Universal 432 
Hammer, Ball peen 8 oz.  Thread pitch, standard SAE Thexston Universal 432
PLIERS TORQUE WRENCHES
Pliers, 12 SNP RNG plier set Snap ring pliers flat tip Torque wrench: 1/2" drive 30 to 250 ft lbs
Pliers, 6 pc vise grip plier set Torque wrench: 3/8" drive 15 to 100 ft lbs 
Pliers, Combination slip joint style 6"  Torque wrench: dial 3/8" drive inch pound
Pliers, Diagonal cutting 7 1/4"  WRENCHES
Pliers, Electrical crimping  Wrench, Adjustable, 10"
Pliers, Flat tip (Duck Bill) snap ring  Wrench, Adjustable, 12"
Pliers, Interlocking/adjustable joint 12"  Wrench, Allen (hex) wrenches, 2mm thru 12mm
Pliers, Locking type, standard 8"  Wrench, Allen (hex) wrenches, 5/64" thru 3/8"
Pliers, Needle nose 7 1/4"  Wrench, Combination, 5/16" thru 1 1/4" (12 point) 
  Wrench, Combination, 6mm thru 22mm (12 point)