|
Roll cabinet toolbox
|
Cape 1/4" or 1/16" Chisel
|
|
Diamond Point 7/32" or 1/8" Chisel
|
Flat 1/2" Chisel
|
|
Flat 3/4" Chisel
|
Circuit tester or test light (12 and 24 volt capability
preferred, 12 volt will suffice)
|
|
10" round, tapered file
|
12" flat mill, bastard, single cut file
|
|
12" three square, bastard, single cut file
|
Two or three cell MagLight or similar style
|
|
Feeler - 45 degree angle, .006" through .35" gauge
|
Feeler - .0015" through .34", go-no-go style gauge
|
|
Thread pitch, metric gauge
|
Thread pitch, standard SAE
|
|
Digital caliper, metal 0-6"
|
Hacksaw: Frame and blades - (24 and 32 teeth per inch)
|
|
Ball peen 8 oz. hammer
|
Ball peen 16 oz. hammer
|
|
Ball peen 40 oz. or 4 lbs. soft face drilling hammer
|
3 to 5 lbs.. Dead blow with soft face hammer
|
|
Jumper Wires: Two each, 2 to 3 feet long with alligator clips, 12
gauge
|
Magnet: Mechanics style with handle about 12" long
|
|
Pocket Rule: 6" standard and metric with pocket clip
|
Outside 0" to 1" capability, SAE micrometer
|
|
Meter:Volt, Ohm, Amps with digital readout and high
impedance (Fluke mfr. Brand, model 115)
|
Tri-Square: Steel combo 12"
|
|
Combination slip joint style 6" pliers
|
Diagonal cutting 7 1/4" pliers
|
|
Interlocking/adjustable joint 12" pliers
|
Locking type, standard 8" pliers
|
|
Needle nose 7 1/4" pliers
|
Long tip, 3/8", length 15" punch
|
|
Brass drift, 1/2" diameter 10 to 12" in length punch
|
Brass drift, tapered 10 to 12" in length punch
|
|
Center punch, 3/8"
|
Pin, set of 6 (3/32", 1/8", 5/32", 3/16", 1/4" 5/16") punch
|
|
Starter, set of 5 (1/8", 5/32", 3/16", 1/4", 5/16") punch
|
Phillips, #1-3"
|
|
Phillips, #2 - 1 1/2"
|
Phillips, #2 - 4"
|
|
Phillips, #2 - 8"
|
Phillips, #3 - 6"
|
|
Torx Set #T10 thru #T30
|
Standard, 3/16" x 3"
|
|
Standard, 1/4" x 4"
|
Standard, 1/4" x 1 1/2"
|
|
Standard, 5/16" x 8"
|
Standard, 3/8" x 12"
|
|
3/8" Drive Ratchet
|
3/8" Driver 3, 6, 12" extensions
|
|
3/8" Drive Standard (SAE) 10 pc socket set, 1/4" thru 3/4" (12
point)
|
3/8" Driver Metric 13pc socket set, 6mm thru 19mm (12 point)
|
|
3/8" Driver Universal swivel socket
|
1/2" Drive Ratchet
|
|
1/2" Drive Standard (SAE) 15pc socket set 3/8" thru 1 1/4" (12
point)
|
1/2" Drive Metric 18pc socket set 10mm thru 27mm (12 point)
|
|
1/2" Drive 3, 5, 10" Extensions
|
1/2" Drive Breaker bar 18" to 24" long
|
|
Combination, 5/16" thru 1 1/4" (12 point) wrench
|
Combination, 6mm thru 22mm (12 point) wrench
|
|
Tubing wrenches, 1/4" thru 7/8" (6 point)
|
Adjustable wrench 10"
|
|
Adjustable wrench 12"
|
Allen (hex) wrenches, 5/64" thru 3/8"
|
|
Allen (hex) wrenches, 2mm thru 12mm
|
12ft standard and metric scale or something similar tape measure
|
|
Tubing Cutter
|
Scissors
|
|
Pocket Scribe
|
Scientific Calculator
|
|
Set of 4 O-Ring Picks
|
Torque wrench: 3/8" Drive 15 to 100lbs. FT
|
|
Scraper
|
Torque wrench: 1/2" Drive 30 to 250 ft lbs.
|
|
Remote Starter Switch: Heavy duty style, 12 gauge wire
|
Torque wrench: dial ¼” Drive inch pound
|
|
12 SNP RNG plier set Snap ring pliers flat tip
|
Safety Glasses: Z-87 with side shields
|
|
Pry bar set -3 sizes
|
15" with 13/16" edge pinch bar
|
|
Rubber tipped and OSHA approved Air Blow Gun
|
Tubing metric, 8mm thru 17mm wrench
|
|
Thread file set (metric and standard)
|
Double flaring kit
|
|
File set w/red vinyl
|
6 pc vise set
|
